Welcome Guest!
In order to take advantage of all the great features that Waterloo Region Connected has to offer, including participating in the lively discussions below, you're going to have to register. The good news is that it'll take less than a minute and you can get started enjoying Waterloo Region's best online community right away.
or Create an Account




Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Weber Street Reconstruction - College to Union
My thoughts: the wires have perhaps been determined to be insufficiently protective from a safety standpoint, at least for people walking into them. It is determined the way to make the system safe is not to replace the wires entirely, but to stop people from walking into them. So this barrier piece is installed. Weird, nonsensical, but does the job...?
Reply


(07-12-2016, 09:09 AM)GtwoK Wrote: Why would it be an after thought? The spot on the posts that the "handrails" are attached to are present on every post, made out of the same treated metal. They had to have been built into the posts initially.

Well, they did just replace all the posts after a year or so of an old-generation post. It's possible that this was added in then.
Reply
See pages previous to this one, old posts had no holes.
Reply
Maybe something is going to get bolted to the new "railing". Notice there is a tapped hole on centre at each end.
Reply
There are holes along the entire length of every rail, every 12-18 inches or so. I think this was stock (or scrap) material that was repurposed.
Reply
But they're painted to match the upright weldments. So they can't just be scrap.
Reply
You can paint scrap
Reply


I agree. And how likely do you think it is that after all the effort to make those beautiful upright weldments, re-fab half of them, that they're then going to just half-ass it by bolting on scrap metal?
Reply
It's not any cheaper to re-work scrap iron for a piece like that... they are already rounded on the ends and the holes are there for whatever part of it is coming next. Flat bar is pretty cheap too compared to the labour of painting and drilling the holes, cutting the edges and all that.
Reply
Yup. And the rounded ends suggest it's plasma/laser/water jet cut out of a big 4x8 sheet anyway.

But what do I know? I'm just a lowly mechanical designer... Rolleyes
Reply
(07-12-2016, 02:21 PM)Viewfromthe42 Wrote: There are holes along the entire length of every rail, every 12-18 inches or so. I think this was stock (or scrap) material that was repurposed.

Sounds like this is the base on which the proper hand rail will be mounted.
Reply
(07-12-2016, 04:53 PM)Canard Wrote: Yup. And the rounded ends suggest it's plasma/laser/water jet cut out of a big 4x8 sheet anyway.

But what do I know? I'm just a lowly mechanical designer... Rolleyes

It's a lot easier to buy the flatbar at the width it is now and just round the edges with a jig by hand. I'd have to look at the edges to see if it's rolled or if it's cut, can't tell from the picture.
Reply
(07-12-2016, 05:05 PM)Markster Wrote:
(07-12-2016, 02:21 PM)Viewfromthe42 Wrote: There are holes along the entire length of every rail, every 12-18 inches or so. I think this was stock (or scrap) material that was repurposed.

Sounds like this is the base on which the proper hand rail will be mounted.

I actually have seen wooden rails mounted on exactly such a metal railing. However, wood makes no sense here, since it is outdoors. I cannot think of another material one would use instead of wood that would resist the elements. Any thoughts?
Reply


This thread was driving me nuts so I swung by tonight. It is definitely stock flat bar (sorry - left my tape measure at home, normally have it with me in my backpack...), with rounded ends by hand. It is also not just re-purposed scrap material - it's an engineered solution.

<blockquote class="twitter-tweet" data-lang="en"><p lang="en" dir="ltr"><a href="https://twitter.com/RegionWaterloo">@RegionWaterloo</a> <a href="https://twitter.com/berryonline">@berryonline</a> <a href="https://twitter.com/janemitchell">@janemitchell</a> What are these flat bars for? Big discussion on <a href="https://twitter.com/WRConnected">@WRConnected</a> about them. <a href="https://t.co/1TCHE7N3qc">pic.twitter.com/1TCHE7N3qc</a></p>&mdash; iain (@Canardiain) <a href="https://twitter.com/Canardiain/status/752977109996408833">July 12, 2016</a></blockquote>

My bet is that BuildingScout has it right on - there will be a flat wood or "plastic wood" railing screwed on top of it. I swear, though, this whole railing fiasco has all the symptoms of someone's first practical real-world project (and perhaps their last...). Yep, it's cute and fancy to draw it all up. Real life? Not everything gets positioned with millimetre accuracy... I can't imagine the nightmare they're dealing with of nearly customizing every single railing piece when they don't fit properly.
Reply
What have I done. Now Twitter is going nuts over this. Nobody has a clue. : smh :
Reply
« Next Oldest | Next Newest »



Forum Jump:


Users browsing this thread: 3 Guest(s)

About Waterloo Region Connected

Launched in August 2014, Waterloo Region Connected is an online community that brings together all the things that make Waterloo Region great. Waterloo Region Connected provides user-driven content fueled by a lively discussion forum covering topics like urban development, transportation projects, heritage issues, businesses and other issues of interest to those in Kitchener, Waterloo, Cambridge and the four Townships - North Dumfries, Wellesley, Wilmot, and Woolwich.

              User Links